The Mighty Gladiator Dual-Use Atomizer: Oumier Maximus (MAX’) RDTA
Oumier Maximus (MAX’) RDTA. After attracting a lot of attention with the WASP NANO RDA, Oumier released the MAX’ RDTA in the second half of 2017. Many users also nicknamed it the “Big Wasp.” How does it perform? Let’s take a closer look together. Packagin
Oumier Maximus（MAX’）RDTA
MAX drip storage dual-purpose atomizer
Attract countless attention with the WASP NANO Hornet RDA
Oumier released MAX ', a RDTA product, in the second half of 2017
Therefore, it is also called "Bumblebee" by many players
How did you do?
Xiao Huangren + Feng will find out with you[Packaging]
Compared to the Hornet RDA
MAX 'RDTA's packaging design and texture have been upgraded to a higher level
The outside is a lemon yellow wrapper
The overall impression creates a delicate vortex texture
Inside is a black bronzing box with heaven and earth cover
Low-key and steady light luxury
The main picture uses tough lines to form a large M
Like two heating coils
It also contains the meaning of unlimited extension of MAX
The back side contains manufacturer information, product specifications, content list, safety warnings and anti-counterfeiting logos[Open the box]
Push open the envelope and open the box
#p#Pagination Title #e#The main body of the MAX 'RDTA and the spare glass chamber are in the eye
Remove the foam compartment, the lower layer is the accessory kit
In addition to regular screwdrivers, spare screws and rubber rings
There is also a pair of wound heating wires and a spare silicone plugbody
MAX 'RDTA gave me a masculine tough guy image
The main body is made of 304 food grade stainless steel
A diameter of 24mm and a height of 41mm does not seem too high in the RDTA
Looks very strong
Mild polishing of the metal surface will not collect fingerprints
It has both brushed texture and good brightness
There is a radium-engraved M-shaped logo on the top cover and on both sides
The overall face value is very high
Except for the gold model I showed (overall gold plating)
Black and stainless steel are also available[Dismantling]
MAX 'is a typical down-oil storage RDTA
In addition to the RDA conventional structure of suction nozzle + top cover + atomization chamber + electrode table
Added a bottom storage silo with a 3ml oil storage capacity[Suction nozzle]
PEI material has first-class thermal insulation effect #p#pagination title #e#
Extend outward and cover the entire top of the atomizer
I like this anti-scalding mouth design, little yellow man so much
The opening has a barbed design similar to a mad dog
Very simple physical shape can effectively block the condensate inlet
I'll give you a full mark for the original little yellow man with a mouth
However, the 810 standard interface can be replaced with a third-party nozzle
Meet your different appearance requirements
[Top cover + atomization chamber]
The intake air can be adjusted steplessly by rotating the top cover
It is a typical oil dripping atomizer structure
Judging from the outer warehouse, the air inlet hole is just an ordinary long strip.
The inner ring is also made in two forms: wide grooves and narrow grooves
The length and width of the air inlet hole can be adjusted according to your own data needs
The inside of the roof is made into a hemispherical dome
Can gather the smoke to make the taste stronger
It also facilitates condensation and reflux[Electrode table]
The design of the electrode table is the essence of most atomizers
MAX 'RDTA is no exception
He is a powerful and powerful general, but he also has a soft heart#p#Pagination Title #e#
There is a silicone plug with a cross opening in the center of the top of the electrode table
After playing multiple RDTA,
Xiao Huang, I also think top oiling is the best way to inject oil
When refueling, the oil filling pipe opens the cross opening
After refueling is over, the silicone gel rebounds and automatically closes
Very smart design and a feature of MAX 'RDTA
Of course, the silicone material is soft and easy to damage
So spare silicone plugs are included in the accessory kit
Double column and four-hole design of upper and lower story structures
This is the first time I have seen it applied to RDTA
Upper cathode, lower cathode
Use heat-resistant Peek gasket as insulation in the middle
Corresponding grooves are made between each thin piece to fit in
Double hair structure with upper left and lower right (or lower left and upper right) threading
The heating wire can be locked individually and is very friendly to newbies
Compared to hex wrenches that are easy to lose and socket screws that are easy to slip
The embedded one-word screws used in MAX 'RDTA also take into account the player's use
Needless to say, the monofilament included in the package
Huge threading holes can also satisfy almost all types of fancy silk
Considering that the width of the air inlet hole and the space in the cabin are large enough
It can also be adapted to ultra-large heating wires #p#pagination title #e#
Double hair is so easy, I don't need to say more
However, the electrode table design with upper and lower layers
The advantage is that you can try more ways to install silk
As shown in the picture, it is not difficult to shoot four shots vertically.
Of course, eight shots, sixteen shots, thirty-two shots
……
Okay, just kidding, I can't do it either
But players with skillful hands can also try it ~
There are four square oil guide holes under the electrode column
The cotton naturally droop from here to reach the oil storage silo
In addition to the oil guide hole, there is also a small circular hole
It relieves pressure and facilitates air discharge during refueling[Oil storage bin + bottom cover]
The yellow oil storage silo made of PEI can easily match with the same PEI nozzle
The spare glass bin makes it easier to observe the remaining oil, but it is fragile
The oil storage bin is sealed by two rubber rings on the bottom cover and the electrode table
No oil leakage from the oil storage silo was found during the testing
The oil storage tank can be screwed directly out of the bottom
Without having to remove the electrodes, the operation is much easier[Experience]
Let's not talk about four and eight shots or something like #p#pagination title #e#
The wire-making method of one-piece screws and upper and lower four holes is very convenient
The oil filling process is very smooth
The silicone plug design with the cross opening is great
simple and effective
The lower oil storage structure of RDTA is not completely enclosed
Xiao Huang, I still suggest that when there is any remaining oil in the oil tank
Try not to place it upside down or horizontally for a long time to avoid oil leaks
In terms of taste, the taste of RDTA is more similar to the RDA.
Pay attention to the full smoke experience at the entrance
The taste is also more directly restored
Therefore, when selecting data, you should first choose low-resistance fancy silk
And the high-degree-of-freedom intake adjustment can also choose the suction resistance you like
In addition, the oil storage structure will replenish oil to the cotton in a timely manner along with the suction.
Compared to the RDA, which will gradually drain out of cotton
The former will provide a fuller taste experience
Of course, fuel consumption will increase accordingly
[Disadvantages]
First, the amount of air intake can be adjusted by turning the top cover
The top cover is laser patterned but not slip resistant
The electrode screw protrudes not obvious enough
#p#Pagination Title #e#For mechanical stick players,
If the positive electrode of the battery is sunken, it can easily form a short circuit
Although the Peek gasket in the middle of the electrode column is heat resistant,
But long-term adjustment of wire burning can still melt easily
Pay attention to the cooling of the heating wire during wire burning
It is a pity that the manufacturer did not include spare gaskets
Push open the envelope and open the box
#p#Pagination Title #e#The main body of the MAX 'RDTA and the spare glass chamber are in the eye
Remove the foam compartment, the lower layer is the accessory kit
In addition to regular screwdrivers, spare screws and rubber rings
There is also a pair of wound heating wires and a spare silicone plugbody
MAX 'RDTA gave me a masculine tough guy image
The main body is made of 304 food grade stainless steel
A diameter of 24mm and a height of 41mm does not seem too high in the RDTA
Looks very strong
Mild polishing of the metal surface will not collect fingerprints
It has both brushed texture and good brightness
There is a radium-engraved M-shaped logo on the top cover and on both sides
The overall face value is very high
Except for the gold model I showed (overall gold plating)
Black and stainless steel are also available[Dismantling]
MAX 'is a typical down-oil storage RDTA
In addition to the RDA conventional structure of suction nozzle + top cover + atomization chamber + electrode table
Added a bottom storage silo with a 3ml oil storage capacity[Suction nozzle]
PEI material has first-class thermal insulation effect #p#pagination title #e#
Extend outward and cover the entire top of the atomizer
I like this anti-scalding mouth design, little yellow man so much
The opening has a barbed design similar to a mad dog
Very simple physical shape can effectively block the condensate inlet
I'll give you a full mark for the original little yellow man with a mouth
However, the 810 standard interface can be replaced with a third-party nozzle
Meet your different appearance requirements
[Top cover + atomization chamber]
The intake air can be adjusted steplessly by rotating the top cover
It is a typical oil dripping atomizer structure
Judging from the outer warehouse, the air inlet hole is just an ordinary long strip.
The inner ring is also made in two forms: wide grooves and narrow grooves
The length and width of the air inlet hole can be adjusted according to your own data needs
The inside of the roof is made into a hemispherical dome
Can gather the smoke to make the taste stronger
It also facilitates condensation and reflux[Electrode table]
The design of the electrode table is the essence of most atomizers
MAX 'RDTA is no exception
He is a powerful and powerful general, but he also has a soft heart#p#Pagination Title #e#
There is a silicone plug with a cross opening in the center of the top of the electrode table
After playing multiple RDTA,
Xiao Huang, I also think top oiling is the best way to inject oil
When refueling, the oil filling pipe opens the cross opening
After refueling is over, the silicone gel rebounds and automatically closes
Very smart design and a feature of MAX 'RDTA
Of course, the silicone material is soft and easy to damage
So spare silicone plugs are included in the accessory kit
Double column and four-hole design of upper and lower story structures
This is the first time I have seen it applied to RDTA
Upper cathode, lower cathode
Use heat-resistant Peek gasket as insulation in the middle
Corresponding grooves are made between each thin piece to fit in
Double hair structure with upper left and lower right (or lower left and upper right) threading
The heating wire can be locked individually and is very friendly to newbies
Compared to hex wrenches that are easy to lose and socket screws that are easy to slip
The embedded one-word screws used in MAX 'RDTA also take into account the player's use
Needless to say, the monofilament included in the package
Huge threading holes can also satisfy almost all types of fancy silk
Considering that the width of the air inlet hole and the space in the cabin are large enough
It can also be adapted to ultra-large heating wires #p#pagination title #e#
Double hair is so easy, I don't need to say more
However, the electrode table design with upper and lower layers
The advantage is that you can try more ways to install silk
As shown in the picture, it is not difficult to shoot four shots vertically.
Of course, eight shots, sixteen shots, thirty-two shots
……
Okay, just kidding, I can't do it either
But players with skillful hands can also try it ~
There are four square oil guide holes under the electrode column
The cotton naturally droop from here to reach the oil storage silo
In addition to the oil guide hole, there is also a small circular hole
It relieves pressure and facilitates air discharge during refueling[Oil storage bin + bottom cover]
The yellow oil storage silo made of PEI can easily match with the same PEI nozzle
The spare glass bin makes it easier to observe the remaining oil, but it is fragile
The oil storage bin is sealed by two rubber rings on the bottom cover and the electrode table
No oil leakage from the oil storage silo was found during the testing
The oil storage tank can be screwed directly out of the bottom
Without having to remove the electrodes, the operation is much easier[Experience]
Let's not talk about four and eight shots or something like #p#pagination title #e#
The wire-making method of one-piece screws and upper and lower four holes is very convenient
The oil filling process is very smooth
The silicone plug design with the cross opening is great
simple and effective
The lower oil storage structure of RDTA is not completely enclosed
Xiao Huang, I still suggest that when there is any remaining oil in the oil tank
Try not to place it upside down or horizontally for a long time to avoid oil leaks
In terms of taste, the taste of RDTA is more similar to the RDA.
Pay attention to the full smoke experience at the entrance
The taste is also more directly restored
Therefore, when selecting data, you should first choose low-resistance fancy silk
And the high-degree-of-freedom intake adjustment can also choose the suction resistance you like
In addition, the oil storage structure will replenish oil to the cotton in a timely manner along with the suction.
Compared to the RDA, which will gradually drain out of cotton
The former will provide a fuller taste experience
Of course, fuel consumption will increase accordingly
[Disadvantages]
First, the amount of air intake can be adjusted by turning the top cover
The top cover is laser patterned but not slip resistant
The electrode screw protrudes not obvious enough
#p#Pagination Title #e#For mechanical stick players,
If the positive electrode of the battery is sunken, it can easily form a short circuit
Although the Peek gasket in the middle of the electrode column is heat resistant,
But long-term adjustment of wire burning can still melt easily
Pay attention to the cooling of the heating wire during wire burning
It is a pity that the manufacturer did not include spare gaskets
