How to Clean Carbon Buildup on E-Cigarette Heating Coils

  E-cigarette heating wire carbon cleaning how to do, a friend of the background message feedback about this problem, has been we share a lot of electronic cigarette use and maintenance issues, but many players are still the pursuit of big smoke and DIY, the beginning of the problem is certainly encountered a lot of problems, we also want to help you as much as possible to think of ways to solve! Regularly share some of the use of electronic cigarettes are easy to encounter small problems in the solution, but also hope that you enthusiastically leave a question, with more relevant knowledge can look through the history of the article to check, and I hope to help some of the newcomers just start friends.

. 　　Electronic cigarette atomizer heating wire why there will be carbon deposits, how to form?   　　The formation of carbon deposits, first of all, there are two main aspects.   　　The first is from the sugar content within the cigarette oil. It can be said that the sweeter the oil, the easier it is to form carbon deposits. The working principle of electronic cigarettes is to vaporize the oil instantly through the high temperature of the heating wire. Then high temperature and sugar have always been natural enemies. Sugar in the heat will be paste, burnt, sticky and other problems, attached to your heating wire and cotton, over time the more intense.   　　End result: very poor taste   　　Similarly the second point, we are talking about carbon buildup also has another reason, lies in the cotton burn resistance. Strictly speaking, it is the paste core. If you choose a poor quality, burn resistance performance of cotton in general, in daily use, in pursuit of large bursts of smoke, smoke oil and can not keep up, can not wet the cotton in a timely manner, then the heating wire will be directly baked cotton, the formation of carbonized blocks, the loss of oil conductivity and oil storage capacity. The heaters will directly bake the cotton, forming carbonized blocks and losing the ability to conduct and store oil. 　　The end result: smoking cotton, smoke, snore! The final result: smoking cotton, smoke snooze throat. 　　In fact, pay attention to these two major problems at the same time, the selection of unsuitable output will also appear paste core and carbon problems. The problem of carbon buildup can also occur when you choose an inappropriate output. 　　So how to try to avoid or delay the formation of carbon? The answer is to avoid or slow down the formation of carbon. 　　When choosing an oil, try not to choose an oil that is particularly sweet and thick. If you happen to be as good as me, then daily use, no matter whether it is a finished product or drip atomizer, do not special frequent mouthful after mouthful. Give the cotton time to absorb the oil and the filament time to cool down. Drip oil as much as possible to ensure that the cotton oil reserve margin is more, do not know suck do not know drip.  ; The oil drop is as much as possible to ensure that the cotton oil reserves more margin, do not know suck do not know drop. 　　In the choice of wattage should also pay attention to, slowly from low to high to pick the most suitable for this oil and this atomizer wattage, to get the best taste at the same time, but also can absolutely reduce the formation of carbon deposits and paste core, reduce the cost of playing smoke. But here by the way carbon is unavoidable. DIY atomizer cotton processing, but also try to play fluffy, increase oil storage capacity. The first thing you need to do is to get rid of the charcoal in the atomizer. 　　How to clean up after the formation of carbon? Or directly change the heating wire?   　　For the finished core, you can only choose to directly replace the cycle in about a week, the cost is higher, but convenient. For the DIY class atomizer with oil drops, here you can try to deal with, increase its service life, after all, a pair of filaments a pair of cotton is still very painful.   　　Methods: We can remove the cotton, low-wattage heating, burning red heating wire quickly quenched into warm water, the choice of warm water in order to minimize the change in the texture of the heating wire, performance. Visible to the naked eye black fine carbon blowing out, two or three times can be. However, it is not recommended that a pair of heating wire repeatedly burned, burned vigorously. Different materials will have its limit, equal to you are in violation of the heat treatment.  . 　　You can also burn red, with a special wire brushing tool — small wire brush, gently brush off the carbon on the heating wire. For the flower wire and NI wire effect is better. Can extend the service life to about half a month to a month and reduce costs. Feel too much trouble friends change a storage oil atomizer, finished atomizer core are available, do not toss to enjoy the fun of electronic cigarettes is also available.