Dead Rabbit RDA Review

  Recently introduced bottom-filling atomizers, especially those dominated by big smoke, are mostly 24mm in diameter, while the Dead Rabbit SQ RDA Dead Rabbit in this review is a bottom-filling atomizer with a diameter of 22mm.

  　　Since it is a single-shot design that allows the user to customize the selection of intake and drip tip, the multi-scenario application from mouthfeel to big smoke atomizer is really attractive as well.   　　DEAD RABBIT SQ RDA Unboxing The package is a very good one, and it's a very good one. 　　The front of the package is the logo of Dead Rabbit, the product name and some lace. The color is very special.   　　Product introduction, content information on the back of the package, the side is also pasted with anti-counterfeiting mark.   　　Packaging list:   　　Hellvape Dead Rabbit SQ RDA Dead Rabbit Atomizer   　　Tool kit (2 hex wrenches, 1 one screwdriver)   　　810 Drip Tip, 510 Drip Tip Adapter, 510 Drip Tip   　　Conventional Electrode Screws   　　Spare kit (rubber ring, screws)   　　The package includes the atomizer body, accessory accessories, and a toolkit, although there are no free coils and cotton, but what should be there is there.     　　DEAD RABBIT SQ RDA Detailed Picture Review   DEAD RABBIT SQ RDA 　　The Dead Rabbit Bottom Filling Atomizer - DEAD RABBIT SQ RDA from HELLVAPE has a diameter of 22MM. The diameter of DEAD RABBIT SQ RDA is 22MM. 　　Both sides of the air intake, front and rear single-shot electrode column. Pre-installed bottom oiling screws, electrode screws can be replaced to become a regular drip atomizer.   　　Although it looks like it is only suitable for lung inhalation of large smoke, but can be adjusted by adjusting the air intake, replace the 510 drip tip, transformed into a tight suction resistance of the mouthfeel atomizer.   　　Product Specifications:   　　Diameter: 22 mm Diameter: 22 mm 　　Height: 24.3 mm (measured, excluding drip tip and 510 electrode)  ; 　　Weight: 34g (measured)   　　Interface: 510 universal interface   　　Drip Tip: 810/510 (adapter required)   　　Single Coil Setup   　　Dual Side Air Intake   　　Material: Stainless Steel, Resin, Delrin   　　Support bottom oiling   　　On the front of the outer compartment is the same dead rabbit logo as the package.   　　After disassembled as shown in the picture, they are the drip tip, top cover, outer compartment, base.   　　DEAD RABBIT SQ RDA drip tip.   　　The Dead Rabbit is supplied with 3 drip tips. 2 x 810 drip tips and 1 x 510 drip tip. A 510 drip tip adapter is also supplied to fit the 510 drip tip.   　　The 510 Drip Tip Adapter is made of metal and it can fit other standard 510 Drip Tips.     　　Resin drip tip   　　The resin drip tip comes pre-installed on the atomizer.   　　Total height: 12.5 mm, Height with nozzle part: 7.5 mm, Diameter: 17.5 mm, Inner diameter: 12.5 mm.     　　DELRIN drip tip DELRIN Drip Tips 　　The black one is Delrin drip tip, the material is different, the specification is also different, especially the inner diameter is reduced, you can choose according to the preference of vaping.   　　Total height: 13.5 mm, height with nozzle: 9.5 mm, diameter: 13.5 mm, inner diameter: 8.5 mm.     DELRIN Drip Tip 　　510 DELRIN Drip Tip   　　If you need mouthfeel, then you need to install the 510 Drip Tip with an inner diameter of 3mm.   　　Total Height: 17 mm, Height with Tip Section: 12.5 mm, Diameter: 14 mm (base), 10 mm (top), 8 mm (recessed), Inner Diameter: 3 mm.       　　Top cover of HELLVAPE C   　　The Dead Rabbit SQ RDA is a two-side air intake structure, with air entering through two intake holes in the outer compartment and blowing straight through the coils.   　　The intake holes are higher, and the top cap intake adjustment holes are a beveled 45° design that blows air diagonally across the coil from top to bottom. It's a simple structure that optimizes airflow while preventing vape oil from escaping as much as possible.   　　By rotating the top cap, you can change the size of the air intake.   　　As you can see, there are 3 small intake holes for flavor, so you can adjust the intake to a small one-sided intake.   　　The inside of the top cover has a dome style construction.   　　DEAD RABBIT SQ RDA Base   　　The electrode posts on the base are a single coil setup with dual posts and dual holes, and the positive electrode post is gold plated. The overall look is like a left and a right rabbit ears. The base is a single coil with two posts and two holes. 　　The locking screws are one screw, and can be tightened with a one screwdriver.   　　There are hexagonal locking screws in the spare parts to choose from, but why mine is 3 hexagonal, 1 word, maybe it is the wrong one.   　　The base oil reservoir on the left and right sides, it does not look big, the depth is not deep, the oil storage capacity is not strong.   The base reservoir is on the left and right sides, and it doesn't look very big or deep. 　　The base and the outer compartment connection is designed with a positioning pin, easy to locate the air inlet hole, but also easy to install the atomizer in the host, but also to prevent the rotation of the top cover to adjust the air inlet, the outer compartment of the accidental movement.   　　DEAD RABBIT SQ RDA electrode screws   DEAD RABBIT SQ RDA Electrode Screws 　　DEAD RABBIT SQ RDA electrode screws pre-installed is the bottom of the oiling screws, the bulge is more obvious, most of the bottom of the oiling box will be very good adaptability.   　　You can remove the bottom oiling screw with the Allen wrench included in the kit.   　　Of course, a regular electrode screw is included in the package for when the bottom oiling is not in use.   　　You can tighten the electrode screw with a screwdriver.   　　The bottom oiling hole is on the base, and a plastic cap diverts the oil to the oil tank on both sides. The plastic cap cannot be removed directly.       　　Filamenting the DEAD RABBIT SQ RDA     　　The Dead Rabbit's positive and negative wire lock holes are wide and roomy, and it's capable of handling anything from flavorful to big smoke different coils. This time I wanted to do a big smoke one and expected the intake to open 3/1.   　　I placed the outer compartment side by side with the base and observed the position of the intake holes relative to the electrode posts so I could get an idea of the mounting height of the coil.   　　After looking at the location, I mounted a coil directly on top. The pins of the coil go through the electrode posts, and I thought it would be better to cut the pins to the right length ahead of time before installing.   　　The coil data I used is: Cornell 24G, 3.0 turns warp, 6 turns.   　　Burn the coil red to remove any impurities from the coil.   　　I used bacon wool and carefully tucked the ends of the cotton into the oil grooves.   　　Then sleeved the outer compartment and checked the position of the intake to the coil. In fact with the outer compartment on, all the space at the bottom of the coil actually holds oil (in drip mode). I also found that there is actually plenty of room on the top of the electrode post, and your options can be very liberal in terms of single shot setups.  #p#Page Break #e#   　　DEAD RABBIT SQ RDA as it looks when installed   　　With HCIGAR / MAGIC BOX   　　With Aspire / Cygnet 80W MOD     with Aspire / Cygnet 80W MOD   　　DEAD RABBIT SQ RDA Summary   　　As a 22MM bottom-fill atomizer, it's fantastic for usability. In many ways, the usability is great.   　　First of all, the small size of 22mm is especially valuable today when 24mm diameter is becoming mainstream. It allows you to use the 810 drip tip, while at the same time using the small intake and 510 drip tip to emphasize the taste, with a high degree of freedom and an abundance of accessories.   　　In addition, the slightly higher intake setting, which blows the coil straight down diagonally from both sides, increases the cooling performance of the coil and concentrates and mixes the atomized smoke more efficiently, with a comfortable wicking resistance and mouthfeel.   　　Finally, good like a rabbit ear electrode post is very easy to silk, reasonable space to make it to the coil compatibility greatly improved, in the process of easy silk, the degree of freedom is also greatly improved.   　　If you're looking for a more unusual atomizer, I suppose there are other, better options out there, but in terms of small size and usability, there shouldn't be too many others to choose from beyond that. At the very least, this is what I consider to be an exceptionally easy to use and very nice atomizer.