Review of the Ambition Mods C-Roll (Cristiano Ronaldo) RDA
Pod systems have driven the retail nicotine salt e-liquid market, and DIY enthusiasts have been paying close attention to atomizers in this category. For a time, 22mm atomizers were largely overlooked, especially in the era when 3mg e-liquid became mainst
Review of the Ambition Mods C-Roll (Cristiano Ronaldo) RDA
The small vaping devices have driven the retail salt nicotine market, and DIY enthusiasts are paying attention to such atomizers. The 22mm diameter atomizers have been somewhat neglected for a while, especially as 3mg e-liquids have become mainstream in an era dominated by large vapor clouds. Some well-designed 22mm products have not received the recognition they deserve. This article will share a product from Ambition Mods, the C-roll (Cristiano Ronaldo) RDA, which is a standard 22mm diameter atomizer.
Inside the packaging tube, the C-roll RDA comes with complete accessories. You will notice that this atomizer, made of 316 stainless steel, has excellent machining and surface oxidation treatment (available in silver, black, and rainbow colors). The height from the drip tip to the bottom does not exceed 30cm, making it compact. Most boxes look better with 22mm atomizers, and for these small devices that require medium to high resistance, the coil data we create often does not apply to the mechanical output of battery devices.
The atomizer's BF screw is hexagonal, which is great.
The C-roll is a true single-coil RDA, with a coil position that is centered enough. The airflow will hit the coil through the downward air channel and swirl in the arc. The height of the wire hole in the electrode post is just right, eliminating the need to adjust the coil height after installation.
There is a limit between the shell and the base, so when we rotate the top cap to adjust the airflow, the shell remains stationary. The PEEK airflow plug leaves some space below, which blocks the bottom fill screw in the photo. When squeezing e-liquid, it will be automatically divided to the cotton on both sides, unlike open-bottom fill RDAs, where even if you lay it on the sofa while squeezing, this designated e-liquid flow method proves to be more efficient, as both sides of the cotton will be moistened simultaneously.
This is an RDA that can have dual or single airflow. From fully open dual holes to adjustable single holes, it can use heating wires with diameters ranging from A1-0.5mm to 0.32mm, with a coil diameter range of 3.0mm to 2.5mm, which is sufficient for drawing 3/6mg e-liquids and small salt nicotine. Compared to some specialized fine wire small vaping atomizers, the C-roll allows you to use 0.5mm thick heating wires with traditional e-liquids, providing satisfactory flavor concentration and heat.
Now let's talk about actual use. First, regarding the choice of devices for medium to high resistance single-coil RDAs, the battery does feel somewhat weak, reminiscent of the days when only KF and mechanical batteries existed, where the feeling of not being able to produce vapor led to the emergence of adjustable devices. Using the C-roll RDA, you can either use it on a regular adjustable mod (with a standard positive screw) or pair it with an adjustable BF box (with a BF positive screw); mechanical BF mods are not suitable for medium to high resistance.
With the popularity of small salt nicotine, the method of saving wire, cotton, and e-liquid has led many users to want to save even the money spent on disposable small devices. Thus, small devices like the C-roll RDA have become active, corresponding to DIY heating wires for salt nicotine, which are generally A1-0.32/0.35/0.4mm. Their classification is simple: use slightly finer wires for tobacco-flavored e-liquids and coarser wires for fruit-flavored e-liquids. If you are using traditional 3/6mg e-liquids, then generally A1-0.4/0.5mm wire with a 3.0mm coil diameter is the most suitable.
When vaping salt nicotine, you can adjust the airflow of the C-roll RDA to a very small setting for high resistance. This is a flawless product, and its emergence coincides with the popularity of small devices. If you need a 22mm RDA to replace a device that requires constant purchase of pods, the C-roll is worth considering. Personally, I prefer using an RDA for these high PG e-liquids. I wonder if others have this experience: facing the same e-liquid, the performance of RDA coils tends to be better than RBA, perhaps due to the washing effect on the coils when dripping e-liquid.
The small vaping devices have driven the retail salt nicotine market, and DIY enthusiasts are paying attention to such atomizers. The 22mm diameter atomizers have been somewhat neglected for a while, especially as 3mg e-liquids have become mainstream in an era dominated by large vapor clouds. Some well-designed 22mm products have not received the recognition they deserve. This article will share a product from Ambition Mods, the C-roll (Cristiano Ronaldo) RDA, which is a standard 22mm diameter atomizer.
Inside the packaging tube, the C-roll RDA comes with complete accessories. You will notice that this atomizer, made of 316 stainless steel, has excellent machining and surface oxidation treatment (available in silver, black, and rainbow colors). The height from the drip tip to the bottom does not exceed 30cm, making it compact. Most boxes look better with 22mm atomizers, and for these small devices that require medium to high resistance, the coil data we create often does not apply to the mechanical output of battery devices.
The atomizer's BF screw is hexagonal, which is great.The C-roll is a true single-coil RDA, with a coil position that is centered enough. The airflow will hit the coil through the downward air channel and swirl in the arc. The height of the wire hole in the electrode post is just right, eliminating the need to adjust the coil height after installation.
There is a limit between the shell and the base, so when we rotate the top cap to adjust the airflow, the shell remains stationary. The PEEK airflow plug leaves some space below, which blocks the bottom fill screw in the photo. When squeezing e-liquid, it will be automatically divided to the cotton on both sides, unlike open-bottom fill RDAs, where even if you lay it on the sofa while squeezing, this designated e-liquid flow method proves to be more efficient, as both sides of the cotton will be moistened simultaneously.
This is an RDA that can have dual or single airflow. From fully open dual holes to adjustable single holes, it can use heating wires with diameters ranging from A1-0.5mm to 0.32mm, with a coil diameter range of 3.0mm to 2.5mm, which is sufficient for drawing 3/6mg e-liquids and small salt nicotine. Compared to some specialized fine wire small vaping atomizers, the C-roll allows you to use 0.5mm thick heating wires with traditional e-liquids, providing satisfactory flavor concentration and heat.Now let's talk about actual use. First, regarding the choice of devices for medium to high resistance single-coil RDAs, the battery does feel somewhat weak, reminiscent of the days when only KF and mechanical batteries existed, where the feeling of not being able to produce vapor led to the emergence of adjustable devices. Using the C-roll RDA, you can either use it on a regular adjustable mod (with a standard positive screw) or pair it with an adjustable BF box (with a BF positive screw); mechanical BF mods are not suitable for medium to high resistance.
With the popularity of small salt nicotine, the method of saving wire, cotton, and e-liquid has led many users to want to save even the money spent on disposable small devices. Thus, small devices like the C-roll RDA have become active, corresponding to DIY heating wires for salt nicotine, which are generally A1-0.32/0.35/0.4mm. Their classification is simple: use slightly finer wires for tobacco-flavored e-liquids and coarser wires for fruit-flavored e-liquids. If you are using traditional 3/6mg e-liquids, then generally A1-0.4/0.5mm wire with a 3.0mm coil diameter is the most suitable.When vaping salt nicotine, you can adjust the airflow of the C-roll RDA to a very small setting for high resistance. This is a flawless product, and its emergence coincides with the popularity of small devices. If you need a 22mm RDA to replace a device that requires constant purchase of pods, the C-roll is worth considering. Personally, I prefer using an RDA for these high PG e-liquids. I wonder if others have this experience: facing the same e-liquid, the performance of RDA coils tends to be better than RBA, perhaps due to the washing effect on the coils when dripping e-liquid.
