A blessing for perfectionists — Pistons RDA vape dripper atomizer

Difficult things in the world must be done with ease; major things in the world must be done with detail. Last time we talked about being lazy, but this time we talked seriously.

For me, winding and installing heating wires is a faster process. as long as the coil does not hit a wall,

Short circuit, that's OK. Anyway, it's covered up and you can't see it. As long as you sip some words as soon as possible is the best way!

But there are a certain number of players, for whom, this is a very important matter. Whether the coil is centered or not directly affects the use of

The mood when using it, but it backfires. There are always those moments that make people annoying. When you adjust it, you burn until it turns black, pinch until it turns out to be deformed, and the coil follows.

But it was so lazy and crooked. Today, I shared the Pistons RDA piston atomizer brought by Maskking(MK), which was born with it.

Mid-placed Buff, and the name of the verb that makes hormones a little impulsive, may give you a different mood.

OK The awkward opening ended, and the chatter started to walk directly ~~~

?

?

The packaging style is relatively simple, the square cardboard box is more regular, and the front is relatively simple and only the Mask king brand name is printed on it.

And LOGO, black and red collocation has persisted since the non-mainstream era.

The inside of the package is quite interesting. The screwdriver actually has a separate position. It also proves that this screwdriver is very fun. The small design makes it

It's more comfortable to use. The familiar accessory package has appeared in the form of an acrylic box this time, with electrode screws *10 finished filigree *4 rubber rings

Fuck. As well as the 510-drip nozzle adapter ring, although the hexagon is easy to slip, the amount of screws does crush this problem.
The piston is a three-stage design with a base drip nozzle housing. It's relatively simple and clear.

The piston is made of the well-known SS316 stainless steel material and has a diameter size of 24mm, which is the current mainstream size.

The height is 35mm when the drip nozzle is included. Through the adapter, the height is almost the same after replacing the 510 drip nozzle. It is not too tall, but also relatively high.

It is routine. You can see from the picture that the screwdriver is different from what you usually see. The bulge is a magnet. No matter how the screws are installed or disassembled,

When it comes to time, it can be sucked directly at the top. Rough gentlemen like me, whose fingers are like carrots. This little change is great for me.

When everyone is at this bottleneck period of equipment innovation, whether it is equipment or accessories, the changes in these small details are actually quite pleasing.

?

?

The top of the cabin cover is stepped. During use, lips will be more comfortable to touch it and will not be as stiff as a right angle.

It is also a small beautification.

However, after using this groove for a long time, you need to use a toothbrush and cotton swabs to clean it. But I think the benefits outweigh the disadvantages here.

In order to highlight the name of the product, a separate space is provided for it. As for beauty and ugliness, we have to measure them separately.

There are two not-large elliptical air inlets on both sides, and the interior of the cabin body is curved with a dome. Figure 3 shows that there are extra small holes at the bottom of the drip nozzle.

The outer eaves, after the drip nozzle is installed, are also prominent inside the warehouse body. It is a relatively small place with obvious uses and relatively effective effects.

Obviously, a certain amount of splashing oil and condensation during use will be blocked here. And the interior of the cabin cover itself is also designed with two sections.

#p#Pagination Title #e#

?

?

The oil groove of the piston is very deep, which is also related to the ramp-shaped air inlet holes. If they are parallel, the result will be different. Although RDA 1

I don't talk about oil storage capacity, but I always pack more deeper. It's quite good at certain moments.

The electrode design is quite interesting. The mid-coil Buff we mentioned at the beginning also appears here.

The positive pole is directly fixed in the center of the base. The positive pole is not perforated and wired, but is recessed. the negative electrode is arranged on the outer eaves of the base,
When installing the heating wire, we only need to directly install the coil and it will be placed in the center, and we almost only need to fine-tune it.

And it will not cause the coil to deform. Here is also a tip in using it

we can fix the positive pole first and then remove the negative pole screw directly.

Adjust the position of the screw foot and put the screw back into place and fix it because the screwdriver is small.

Magnets make it extremely convenient to remove screws. Of course, it is possible not to remove it, but the coil is easy to deform. Pay attention.

And there are grooves on the outer eaves, so the scissors are erected to easily cut the silk feet. However, it is recommended that manufacturers deepen the grooves, so that the scissors

It can be extended more and easier to operate. Otherwise, it would be a little difficult to deal with thicker silk with only the tip of scissors.

In addition to the regular CE logo, product name LOGO, the bottom of the base also carries an independent number.

?

?

The drip nozzle is made of pei material, which is also familiar to everyone. Through the 510 adapter accessories, you can replace the small-diameter drip nozzle. and is replacing it

After the small drip nozzle, the face value is still acceptable, but the tactile experience at the entrance is not as good as the original drip nozzle.

and i personally think that by replacing the drip nozzle,

It feels a little awkward. Maybe there should be my magical laugh here.

?

The piston has the ability to control silk, but personally recommend using a ring diameter of 3.0 or less.

The speed and simplicity of silk loading are the same as usual, but it is a proper center placement without almost adjustment. I feel very happy.

It should be noted that although the silo cover is high and the air intake is sloped, the coil height needs to be paid attention to achieve direct blowing effect.

The 7mm deep oil groove of the piston also performs well in use. Adding oil can last for a long time, and I feel happy again.

A piston whose size of the air inlet hole does not count. During use, even if the air inlet is fully opened, there will be no sense of emptiness, and it can still be clear and obvious

When you feel the suction resistance, it is already very suitable for small lung suction when you reduce the intake air to below 50%. However, the silk is silk after all.

It is still relatively guaranteed to adjust the amount of smoke. In terms of tobacco oil, I personally think that the piston is more suitable for compound fruit-flavored tobacco oil.

At the beginning, I was worried that the cabin wall was too thin, and the mouth might be hot when using it did not happen, because the top was a thickened area.

Reason, the parts we can contact will not be too hot. On the contrary, the thin chamber walls speed up the heat dissipation a lot, which is an unexpected surprise.

?

?

Some equipment makes it easier for us to operate and lower the threshold for newcomers, but Piston has simplified it on a serious basis.

Whether it is a newcomer, a disabled party, or a lazy person like me in the terminal stage of cancer, it would be great to easily make beautiful coils.

Although there is room for improvement in small details, such as the depth of the negative wire cutting groove, there is no perfection in the world.

True perfection may only exist in fantasy.

As a 24mm conventional equipment, the piston RDA atomizer may not surprise us too much, but the details are true.

It is quite satisfactory in fact. Not only does it look good, it also has a good taste and fog-making ability.

If it happens to solve some of your needs, you might as well pay attention and take a look..

Happy time passes very quickly, and then we will say goodbye again ~~ OK This experience sharing ends here..